ANALISIS SIMULASI PEMBEBANAN STATIS TERHADAP SAMBUNGAN DOWEL PADA PRODUK CURVED FEET STOOL
https://poltek-furnitur.ac.id/
Politeknik Industri Furnitur dan Pengolahan Kayu
Indonesia
https://poltek-furnitur.ac.id/
Politeknik Industri Furnitur dan Pengolahan Kayu
Indonesia
https://poltek-furnitur.ac.id/
Politeknik Industri Furnitur dan Pengolahan Kayu
Indonesia
Abstract
Kontribusi dengan persentase 80% terhadap produk ekspor mebel, furnitur menjadi industri dengan potensi pasar yang besar. Namun demikian, sambungan pada produk furnitur merupakan bagian yang perlu diperhatikan, karena pada bagian ini sangat rentan terjadi patahan atau kerusakan. Pengujian produk prototipe perlu sumber daya dan waktu lebih, sehingga dikembangkan metode pendekatan untuk memperoleh data hasil pengujian kekuatan produk tanpa membuat prototipe atau lebih dikenal dengan metode analisis elemen hingga (FEA). Penelitian ini bertujuan untuk menguji kekuatan sambungan dari sebuah stool yang dipasangkan pasak kayu dengan ukuran Ø8, Ø10 & Ø12 mm sebagai konstruksinya. Hasil simulasi pembebanan statis menunjukkan jika aplikasi pasak kayu Ø12 mm mampu menahan beban 60kgf lebih baik dibandingkan dengan pasak kayu Ø8 dan Ø10 mm. Tegangan von misses maksimum sebesar 23,14 MPa masih jauh dibawah nilai tegangan luluh material. Selain itu pergeseran dan regangan maksimal hanya senilai 0,562 mm dan 0,0011 secara berurutan.
Keywords
References
Abidin, Z., Rama, & Ridho, B. (2015). Analisa Distribusi Tegangan Dan Defleksi Connecting Rod Sepeda Motor 100 Cc Menggunakan Metode Elemen. Jurnal Rekayasa Mesin, 15(1), 30–39.
Bardak, T., Tankut, A., Tankut, N., Aydemir, D., & Sözen, E. (2017). The Bending and Tension Strength of T-Type Mortise and Tenon Joints Bonded with Polyvinyl Acetate Nanocomposites. Maderas: Ciencia y Tecnología, 19, 51–62.
Cai, L., & Wang, F. (1993). Influence of the stiffness of corner joint on case furniture deflection. Holz Als Roh- Und Werkstoff, 51, 406–408. https://doi.org/10.1007/BF02628238
Callister, W. D. J. (2007). Materials Science and Engineering; An Introduction. In John Wiley & Sons, Inc. (7th ed., Vol. 26, Issue 14). John Wiley & Sons, Inc. https://doi.org/10.1007/BF01184995
Fabbri, A., Minghini, F., & Tullini, N. (2022). Monotonic and cyclic pull-pull tests on dowel-nut connector in laminated veneer lumber made of European beech wood. Construction and Building Materials, 359, 129461. https://doi.org/https://doi.org/10.1016/j.conbuildmat.2022.129461
Fu, H., Li, Z., Alhaddad, W., & He, M. (2024). Experimental evaluation and theoretical prediction of dowel-type joints connecting laminated veneer lumber with wood dowels. Construction and Building Materials, 416, 135248. https://doi.org/https://doi.org/10.1016/j.conbuildmat.2024.135248
Hao, J., Xu, L., Wu, X., & Li, X. (2020). Analysis and modeling of the dowel connection in wood T type joint for optimal performance. Composite Structures, 253, 112754. https://doi.org/https://doi.org/10.1016/j.compstruct.2020.112754
Hassan, R., Ibrahim, A., Ahmad, Z., & Nizam Shakimon, M. (2014). Factor of Safety for Dowelled-Double Shear Kempas and Kapur Connections BT - InCIEC 2013 (R. Hassan, M. Yusoff, Z. Ismail, N. M. Amin, & M. A. Fadzil (eds.); pp. 61–73). Springer Singapore.
Hu, W., Luo, M., Liu, Y., Xu, W., & Caglar Konukcu, A. (2023). Experimental and numerical studies on the mechanical properties and behaviors of a novel wood dowel reinforced dovetail joint. Engineering Failure Analysis, 152, 107440. https://doi.org/https://doi.org/10.1016/j.engfailanal.2023.107440
Kementerian Perindustrian, B. P. (2015). Laporan kinerja Kementerian Perindustrian.
Kuşkun, T., Smardzewski, J., & Kasal, A. (2021). Experimental and numerical analysis of mounting force of auxetic dowels for furniture joints. Engineering Structures, 226(September 2020). https://doi.org/10.1016/j.engstruct.2020.111351
Lam, F., Li, Y., & Li, M. (2016). Torque loading tests on the rolling shear strength of cross-laminated timber. Journal of Wood Science, 62(5), 407–415. https://doi.org/10.1007/s10086-016-1567-2
Limanseto, H. (2023). Tingkatkan Kualitas dan Daya Saing Produk, Pemerintah Bidik Pasar Ekspor Industri Furnitur Makin Luas. www.ekon.go.id
Purwanto, A. A., Rahmat, B., Widiyanto, W., Wijayanto, A., Muhamad, S., Mulyosari, D., & Nurmadina, N. (2024). PENGARUH JENIS KONSTRUKSI KLASIK DAN MODERN TERHADAP KEKUATAN PRODUK BERBASIS KAYU. Jurnal Tengkawang, 14(1), 10–22. https://jurnal.untan.ac.id/index.php/tengkawang/article/view/75399
Rahmat, B., Mulyosari, D., Purwanto, A. A., & Widiyanto, W. (2023). Pengaruh Posisi Sambungan Konstruksi Kayu Terhadap Dedain Produk Mebel Berbahan Dasar Kayu. Jurnal Kreatif : Desain Produk Industri Dan Arsitektur, 11(1), 8. https://doi.org/10.46964/jkdpia.v11i1.336
Rahmat, B., Widiyanto, W., Purwanto, A. A., Wijayanto, A., Muhamad, S., Mulyosari, D., & Nurmadina, N. (2024). Studi Eksperimental Uji Kekuatan Sambungan Klasik dan Sambungan Modern pada Produk Furnitur. JIE (Journal of Industrial Engineering): Scientific Journal on Research and Application of Industrial System, 09(1), 1–13. http://e-journal.president.ac.id/presunivojs/index.php/journalofIndustrialEngineerin/index
Rescalvo, F. J., Portela, M., Cruz, C., Bravo, R., & Lorenzana, J. A. (2024). Relationship between the acoustic emission and the strain field in finger joints of engineered wood products for construction. Engineering Failure Analysis, 162, 108411. https://doi.org/https://doi.org/10.1016/j.engfailanal.2024.108411
Saputra, E. B., Zohari, A., Andriansyah, & Sulistyo, W. B. (2023). The Analysis Static of Chassis Robot Arm as Design Modification Induction Melting Furnace Machine Using FEA Method. Journal of Renewable Energy and Mechanics, 6(02), 85–98. https://doi.org/10.25299/rem.2023.vol6.no02.14344
Tankut, A. N., & Tankut, N. (2011). Section modulus of corner joints in furniture frames as engineering design criteria for their efficient construction. Materials & Design, 32(4), 2391–2395. https://doi.org/https://doi.org/10.1016/j.matdes.2010.10.027
Tas, H. (2010). Strength properties of L-profiled furniture joints constructed with laminated wooden panels. Scientific Research and Essays, 5, 545–550.
Tuhkanen, E., Mölder, J., & Schickhofer, G. (2018). Influence of number of layers on embedment strength of dowel-type connections for glulam and cross-laminated timber. Engineering Structures, 176, 361–368. https://doi.org/10.1016/j.engstruct.2018.09.005
Yang, S.-L. (2023). The Finite Element Approach (pp. 7–21). http://dx.doi.org/10.1007/978-981-99-1425-8_2
Yerlikaya, N. Ç. (2012). Effects of glass-fiber composite, dowel, and minifix fasteners on the failure load of corner joints in particleboard case-type furniture. Materials and Design, 39, 63–71. https://doi.org/10.1016/j.matdes.2012.02.024
Industrial Engineering Departement - Ph.D. Student
Article Tools
Email the author (##plugins.block.readingTools.loginRequired##)